我公司是以生產、銷售、維護氣浮設備為一體的公司，近年來公司不斷發展技術力量，創新生產技術手段，生產的產品銷往全國各地，受到客戶的一致好評，讓大家了解一下氣浮設備的操作規程有哪些。

氣浮設備，包括氣浮機等，在污水處理中是一種常用的設備，那么它的操作規程，我們知道多少呢？據專家介紹，主要有技術參數、運行操作、注意事項以及維護保養，下面來具體介紹這些內容。

1.技術參數

(1)一般采用機械反應，反應時間為15分鐘。

(2)氣浮區接觸室的上升流速為47mm/秒，分離后為0.46mm/秒。

(3)一般回流比為30%，處理水量為0.25—0.4m3/小時。

2.運行操作

(1)配好混凝劑，并加入投藥裝置，啟動空壓機將壓縮空氣輸入溶氣。

(2)等到壓力溶氣罐的壓力達到2—3kg/cm2時，啟動配有電動的單相電水泵，然后緩慢打開閥門，將清水輸入溶氣罐進行溶氣，但要注意液面計。

(3)等到溶氣罐液面計水位達到三分之一后，打開釋放閥門將溶氣水輸入反應池。

(4)調節水泵閥門，使得水位保持在1/3—1/2處；調節氣浮池排水閥門，使得水位保持在排渣口，然后開始正常運行。

3.注意事項

(1)在使用前，應對電器設備進行徹底檢查，檢查是否正常。

(2)要隨時注意壓力溶氣罐的壓力，不能超過4kgcm2。

(3)單相電水泵不能斷水，更不能空載運行，以免損壞單相電水泵。

(4)要保持釋放器的清潔，如果釋放器被堵塞，則會影響氣浮效果。

(5)不能用濕手接觸帶點開關、插座等，如果需要檢查，應由電工進行。

4.維護保養

(1)設備運轉應按有關工藝操作規程進行運行，嚴禁違規操作。

(2)要愛護設備儀器，凡有腐蝕性的化工原料，應避免與電器、金屬相接觸，以免被腐蝕。

(3)操作運行結束后，應清洗設備儀器，以待再次使用。更多氣浮設備知識請登錄：www.wxwoma.com。

中譯英：

Our company is the production, sales, maintenance of air flotation equipment for the whole company, the development of the company technical force is constantly in recent years, technology innovation and production, products are sold throughout the country, by the customer the consistent high praise, today let everyone know about what are the procedures of floatation equipment.

Flotation equipment, including air flotation machine, in the sewage treatment is a kind of commonly used equipment, then its operating procedures, what do we know? According to experts, the main technical parameters, operation, precautions and maintenance, here to introduce these contents.

1 technical parameters

(1) the mechanical reaction, the reaction time is 15 minutes.

(2) flotation zone contact chamber flow rate for 47mm/ seconds, after the separation of 0.46mm/ seconds.

(3) general reflux ratio is 30%, treated water is 0.25 0.4m3/ hours.

2 operation

(1) with good coagulant, and joined the dosing device, start the air compressor compressed air input of dissolved gas.

(2) when the pressure air tank pressure reaches 2 3kg/cm2, start with a single-phase electric water pump motor, and then slowly open the valve, the water input of dissolved gas saturator, but should pay attention to the liquid level gauge.

(3) until the dissolving tank liquid level gauge water level reached 1/3 after the release valve, open the gas dissolved water input reactor.

(4) Regulation of pump valve, the water level maintained at 1/3 - 1/2; adjusting flotation tank drain valve, the water level maintained at discharging port, and then began to normal operation.

3 note

(1) before use, in response to the electrical equipment for a thorough check, check whether it is normal.

(2) to watch the pressure dissolved gas pressure at any time, can not be more than 4kgcm2.

(3) single-phase electric water pump can not be cut off, but not running, so as not to damage the single-phase electric water pump.

(4) to keep the release of clean, if the release is blocked, it will affect the flotation effect.

(5) does not contact with wet hands with a switch, socket, if you need to check, by electrical.

4 maintenance

(1) equipment operation should be run in accordance with the relevant technical operation rules, no violation operation.

(2) to protect the equipment and instrument, where corrosive chemicals, should avoid contact with electrical appliances, metal, in order to avoid corrosion.

(3) after the operation, should be cleaning equipment, to be used again. Flotation equipment more knowledge please login: www.wxwoma.com.